Kantech KT-PC4204 User Manual download pdf

Tel.: 1 (450) 444 2030 • Toll Free: 1 888 222-1560 • Fax: 1 (450) 444 2029 • Internet: www.kantech.com DN1246-0404

Kantech Systems

KT-PC4204

4 Rela

Output and Power Suppl

1. Introduction

The KT-PC4204 is an output module with four programmable relays and can be

used to repower the Combus (see KT-300 installation manual in the Combus

Repower Section). This module is also used for elevator control.

Note: Do not use any power supply other than the KT-PC4204 to repower the

Combus. If a power supply other than the KT-PC4204 is used, the Combus

repower function will not operate as intended.

2. Specifications

• Current Draw: 30 mA (from Combus)

• 16VAC/40VA transformer required

• Maximum 7Ah battery required

• Connects to the controller via 4-wire Combus

• Four programmable relay contacts rated 2A, 30VDC

• AUX current: 1.0A max.

• Tamper contact input

• Can be used to repower the combus

• Can be used for elevator control

3. Installing the KT-PC4204

3.1. Unpacking

The KT-PC4204 package should include the following parts/items:

• One (1) KT-PC4204 circuit board

• One (1) ground wire assembly

• Five (5) plastic standoffs

• One (1) 5A replacement fuse

• One (1) installation instructions sheet

3.2. Mounting

The KT-PC4204 should be located inside a compatible cabinet (Kantech part no.

KT-4051CAB), mounted in a dry and secure location. Preferably, it should be

placed at a convenient distance from the connected devices.

Perform the following steps to mount the unit:

1. Press the five (5) plastic standoffs through the mounting holes at back of the

cabinet,

2. Secure the cabinet to the wall in the desired location. Use appropriate wall

anchors when securing the cabinet to drywall, plaster, concrete, brick or

other surfaces,

3. Press the circuit board into the plastic standoffs to secure the module to the

cabinet.

Once the unit is mounted, wiring may be started.

3.3. Installation and Wiring

Before beginning to wire the unit, ensure that all power (AC transformer and

battery) is disconnected from the KT-300 controller.

Perform the following steps to complete wiring:

1. Connect the four Combus wires to the KT-PC4204. Connect the red, black,

yellow and green Combus wires to the RED, BLK, YEL and GRN

terminals, respectively.

If the module is being used for Combus Repower, connect the Combus wires

according to the following diagram. For this option, Jumper J1 must also be

set for “Combus Relay.”

2. Complete all output wiring,

3. Connect the external tamper switch, if used.

Consult the above wiring diagrams for further information.

1 2

KT-PC4204 1
Terminal Connections 2

Summary of Contents

Page 1 - KT-PC4204

Tel.: 1 (450) 444 2030 • Toll Free: 1 888 222-1560 • Fax: 1 (450) 444 2029 • Internet: www.kantech.com DN1246-0404 Copyright  2004 Kantech System

Page 2 - Terminal Connections

Tel.: 1 (450) 444 2030 • Toll Free: 1 888 222-1560 • Fax: 1 (450) 444 2029 • Internet: www.kantech.com DN1246-0404 Copyright  2004 Kantech System

Comments to this Manuals

No comments

Kantech KT-PC4204 User Manual

Browse online or download User Manual for Accessories for electrical Kantech KT-PC4204. Kantech KT-PC4204 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for electrical Kantech KT-PC4204